IntesisHome Specific WIFI device by AC brand offers you the possibility to have all the control of your AC unit in your hand. These WiFi devices communicates with the AC Indoor Unit using the manufacturer communication protocol. That means communication is 100% bidirectional and all the information showed in our app or web is real. In addition thanks to this communication we show you or send you by e-mail extra information as per example: Error Signals, Code of the Error, Description of the Error. With some AC manufacturers we can inform you also about the Outdoor Temperature, Energy Consumption, etc.
What's included in the box
- Specific AC connection wire
- External WiFi antenna
- External temperature sensor
- IntesisHome Brand Specific Controller
Specific WiFi devices use the proprietary communication protocol of each AC manufacturer allowing real bidirectional communication with the AC system, offering also advanced parameters like error signals, error codes, Power Consumption, etcPanasonic Sanyo Daikin Fujitsu Fujitsu General Hiyasu Fuji Electric LG Mitsubishi Heavy Industries Toshiba
On-the-go controls using your Smart Phone
- Operating modes: Cool, Heat, Auto, Fan, Dry
- Temperature point
- Fan Speed
- Ambient temperature
- Timer & Scenes
- Programmable yearly calendar
Monitoring Functions (depends on A/C model)
- Exterior temperature monitoring
- Current energy consumption
- Total energy consumption
- Set point temperature limitation
- Amount of hours the AC is On
- Signal error
- Error code and Description
- Error messages by email
Enhanced smart capabilities (via third party services)
- Voice Commands
- Interaction with other Smart Home devices from Nest, Belkin, WeMo, Philips Hue, etc
- iOS VoiceOver Support
What you need
1.1. Ensure that your air conditioner, heat pump or air to water unit is compatible with the system.
Check compatibility list to verify that this is accomplished.
1.2. Acquire an IntesisHome device.
Before start using IntesisHome Application, you will need to acquire an IntesisHome device.
1.3. Internet connection in the building where the air conditioner, heat pump or air to water system is installed.
IntesisHome is a cloud based application. Therefore, Internet connection is needed for its use. To ensure this, please:
A) Check Wi-Fi network status.
Before starting the set up process, check that Wi-Fi signal level is good enough. To do it so, please pick up your Wi-Fi device (smartphone, tablet or laptop) and check Wi-Fi networks available. Stay as close as possible from the IntesisHome device and have a look on the available Wi-Fi networks*. Check that from where you are, you can access your own Wi-Fi network (the network you have at home or the office) and a network that starts with INTESISHOME.
*Depending on the OS you are using, information regarding Wi-Fi networks can be found in different places. Refer to your OS help center if you don’t know where to find this information and/or visit our connectivity section in this same site.
B) Check that you have enough Wi-Fi signal level.
The web browser should display a list of available Wi-Fi networks. Look for the name of your Wi-Fi network* and make sure that the signal level associated to it is Good, Very Good or Excellent. If this is not the case, please try to move your Access Point (AP) or router as close as possible to the IntesisHome device. If this is not possible, please visit our connectivity section in this same site for more information and possible solutions.
* The name of your Wi-Fi network is set in your Access Point (AP) or router. Check any of those equipment manuals if you don’t know your Wi-Fi network and want to know it or change it.
1.4. A Wi-Fi device with access to the Internet.
As mentioned before, IntesisHome needs Internet connectivity. To run IntesisHome Application and to control the indoor unit(s) you will need at least one device with Internet connectivity (smartphone, laptop or tablet). Moreover, to carry out the configuration step, you will need a Wi-Fi device (smartphone, laptop or tablet) to access the IntesisHome device and configure it properly. In case you want to use the App available for iPad, iPhone, iPod or Android devices, you will also need one of these devices, which need to be purchased apart.
How to install and configure
1. Install IntesisHome device.
Please, follow instructions on the Installation Manual to connect the IntesisHome device to the indoor unit. Remember that installation procedure should be performed by an authorised installer, so contact with your local installer to perform this step.
Result: If installation process has been successful, IntesisHome device LED will be steady GREEN.
If not, please ensure that the air conditioner, heat pump unit or air to water system is connected to mains. If problem still persist, ask you installer to check connections and wiring installation to ensure everything is OK.
2. Configure IntesisHome device.
Before enjoying IntesisHome, you need to configure your IntesisHome device. To do it so, please follow instructions on the Quick Start Guide and the IntesisHome Device Configuration site.
Result: If configuration process has been successful IntesisHome device LED will blink GREEN,YELLOW, RED and finally turns OFF. See image below to check.
If your device is not following this sequence, please check the LED status table below to try to find out which has been the problem.
|Green||Blinking||Checking device configuration parameters (up to 2 minutes)|
|Yellow||Blinking||Downloading configuration. Wait (up to 2 minutes)|
|Red||Blinking||Connecting to access point and server (up to 2 minutes)|
|Red/Green||Alternate Blinking||Error Connecting to Access point or router. Try to connect again and make sure you write the correct password|
|Yellow/Green||Alternate Blinking||Server not reached. Check if there is Internet connectivity on your Access Point or router|
|Blue||Blinking||Performing WPS connection (up to 2 minutes)|
|White||Blinking||IntesisHome device identification|
Remember that before start using the IntesisHome device, you need to register yourself as a user and the device too. See How can I register my IntesisHome device? to get more information.