Z-Wave.Me Z-Uno
Hubs

Z-Wave.Me Z-Uno

Availability: In Stock
  • Vendor:ZWave.Me
$110.00

The Z-Wave.Me Z-Uno is the first and only easy to use developer board that allows you to create your own Z-Wave device without deep knowledge of Z-Wave protocol or programming. Z-Uno is a mix of Z-Wave home automation radio protocol power and Arduino simplicity. Being inspired by Arduino project Z-Uno inherits all concepts of easy-to-use hardware and software solutions, keeping maximum flexibility.

Z-Uno is a fully DIY product. It is made for those who are limited by existing choice of Z-Wave products and wants to extend their smart homes with more sensors and actuators: connect LEDs, buttons, switches, motors or any low voltage sensor including most of Arduino compatible sensors.

Z-Uno programming is done by writing sketch in simplified C language and loaded into Z-Uno using Arduino IDE. Many examples and comprehensive tutorials will help you to make your own project.

Being Z-Wave Plus certified device, Z-Uno is the perfect companion for your RaZberry gateway. Z-Uno is compatible with other controllers too: among them Fibaro Home Center 2/Lite, Vera Edge and Zipato Zipabox.

  • First and only easy to use developer board that allows you to create your own Z-Wave device
  • Inspired by Arduino project Z-Uno inherits all concepts of easy-to-use hardware and software solutions
  • Do-It-Yourself product: Compatible i.a. with LEDs, pushbutton, switch, motors or low voltage sensors
  • Ideal addition for RaZberry gateway or other controller (e.g. Fibaro Home Center, Zipato Zipabox...)
  • Wireless Technology: Z-Wave Plus

Hardware specification

  • 28 kB Flash memory for your sketches
  • 2 kB RAM available
  • Z-Wave RF transmitter at 9.6/40/100 kbps
  • 26 GPIO (overlaps with special hardware controllers)
  • 4 ADC
  • 5 PWM
  • 2 UART
  • 1 USB (serial port)
  • 1 SPI (master or slave)
  • 1 Interrupt
  • 2 service LED, 1 service button
  • 1 user test LED

Power modes

  • USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • always on, sleeping or FLiRS (Frequently Listening)

Z-Wave supported features

  • Z-Wave Plus compliant
  • Available in all Z-Wave frequencies
  • Out of the box support of AES 128 bit Security
  • Upgrade via USB or radio (Z-Wave OTA)
  • Multichannel (10 channels)
  • 5 Association groups
  • Controls switches, dimmers, door locks(future feature) and scenes
  • Works with gateways and/or directly with other Z-Wave devices
  • Channel types: Binary Switch; Multilevel Switch; Colour Switch; Binary Sensor; Multilevel Sensor

Dimensions

  • L×W×H: 39×20×16 mm (PCB dimensions with all components)
  • L×W×H: 39×20×7 mm (PCB dimensions with PLS and battery connectors removed)
  • Antenna lenght: 86 mm (89 mm with isolation), can be bent to better fit your dimensions
  • Weight: 7 g
  • Antenna type: wire antenna 86 mm for 865-870 MhZ
  • Alternative antenna: optional u.fl connector can be soldered (to RF2 pads)

Electrical characteristics

  • Digital pin in logical 1: > 2.1 V, leakage current 10 μA
  • Digital pin in logical 0: < 0.9 V, leakage current 10 μA or 40-120 μA (with internal pull-up enabled)
  • Internal pullup resistor: 15-20 kΩ (at +25°C)
  • Digital pin out logical 1: > 2.4 V, max current sourcing 8 mA (16 mA for digital pins 3-6)
  • Digital pin out logical 0: < 0.4 V, max current sinking 8 mA (16 mA for digital pins 3-6)
  • Total max current sourcing from GPIO pins: 120 mA
  • Power consumption on 3.3 V: in always listening mode 50 mA, in sleep mode 1 mA (about 7 μA if one DC-DC is unsoldered), in FLiRS mode 1 mA (about 70 μA if one DC-DC is unsoldered)
Z-Uno Quick Start Guide (Size: 1.45 MB)